樓承板在廠家生產加工制造時如果在鋼柱處沒有連接，因此需要安裝連接鋼筋、遍布鋼筋和附加鋼筋。那么濟南樓承板增加鋼筋連接有什么事項了解呢？下面一起來了解一番。

　　If there is no connection in the steel column when the floor bearing plate is manufactured by the manufacturer, it is necessary to install connecting steel bars, all over steel bars and additional steel bars. So what matters do you know about the reinforcement connection of ji 'nan floor bearing plate? Let's take a look.

　　用同等級、同型號同直徑的鋼筋套上鋼架，然后擰下來，把外綁扎斷電焊。還要保證連接好后，還要檢查對面兩側的鋼桁架是否在同一水平面上。

　　With the same grade, the same model with the same diameter of the steel frame, and then screwed down, the external binding broken welding. Once connected, check that the opposite steel trusses are on the same level.

　　附加鋼筋的電焊需要單層焊接，焊接長度為10d，避免鋼桁架側邊錯位。設計圖紙應注明預埋孔，并在孔周圍設置肋板。當樓承板遇到鋼梁須在現場進行激光切割而平面外觀發生變化時，激光切割位置損壞也需要設置肋板，并用橡膠修復傷口。

　　The electric welding of additional steel bars requires single-layer welding with a welding length of 10d to avoid side dislocation of steel trusses. The design drawings shall indicate the embedded holes and provide ribs around the holes. When the floor bearing plate meets the steel beam, it must be cut by laser on site and the appearance of the plane changes. When the laser cutting position is damaged, it is necessary to set up the rib plate and repair the wound with rubber.

　　在鋼筋板的深層鋼桁架橡膠支座中，每邊不得小于斷承鋼筋總面積的一半且不小于212。垂直鋼桁架樓承板定向加水桁架上鏈墻的面筋，額外的水加固墻*混凝土加固蓋須確保至少15毫米。

　　In the deep rubber bearings of steel trusses of reinforced plates, each side shall not be less than half of the total area of broken reinforcement and not less than 212. Vertical steel truss floor bearing plate orientated water truss upper chain wall of gluten, additional water reinforcement wall * concrete reinforcement cover shall ensure at least 15 mm.

　　在粘貼鋼筋的過程中，應非常注意對已鋪設好的樓承板的保護，更不要在熱鍍鋅板上行走或踩踏。禁止旋轉和斷開鋼桁架：如果須斷開，應使用通信型號和規格的鋼筋將鋼桁架重新連接到鋼桁架上。

　　In the process of sticking steel bar, special attention should be paid to the protection of the floor bearing plate has been laid, not to walk or trample on the hot galvanized plate. Do not rotate and disconnect steel trusses: if disconnection must be made, the steel trusses should be reattached to the steel trusses using rebar of communication type and specification.

　　濟南樓承板附加鋼筋工程及管道鋪設：

　　鋼筋板連接鋼筋、橡膠承重鋼筋及與鋼筋桁架樓板垂直夾角的鋼筋建議按設計規定設置。并用鋼桁架綁扎，并用雙絲雙扣扎牢。鏈條鋼筋的下部或上下鋼筋應放置在鋼桁架暗鋼筋的上側。鋼筋桁架總面積的一部分鋪裝完畢后，需要立即將鋼筋橡膠支座與鋼筋與鋼筋桁架垂直角連接的鋼筋綁扎，以保證鋼筋板連接為一個整體。由于鋼桁架樓板的危害，樓板內的管材應正確選擇。

　　Additional reinforcement engineering and pipeline laying of Jinan floor bearing plate:

　　The steel bar connecting the steel plate, the rubber bearing steel bar and the steel bar with the vertical Angle of the steel bar truss floor must be set according to the design provisions. And steel truss binding, and double wire double buckle binding. The lower or upper steel bars of the chain shall be placed on the upper side of the concealed steel bars of the steel truss. After paving part of the total area of the steel truss, it is necessary to bind the steel rubber bearing with the steel bar and the steel bar truss at vertical angles to ensure that the steel plate is connected as a whole. Due to the harm of steel truss floor, the pipe in the floor should be chosen correctly.

　　樓承板增加鋼筋連接有什么事項了解？ 總之，在進行增加鋼筋鏈接的過程中需要操作人員正確的使用方法方式以及步驟，避免危險隱患發生。更多內容就來網站m.liondatech.com咨詢吧！

　　What matters do you know about the reinforcement connection of the floor bearing plate? In short, in the process of increasing the reinforcement link, the operator needs to use the method and steps correctly to avoid the occurrence of danger and hidden dangers. More content to the website m.liondatech.com consultation!